Connecting a Flightscope Device to E6 Connect

Connecting a Flightscope Device to E6 Connect

Connecting your FlightScope device (such as the Mevo+, X3, or Xi) to E6 Connect is a precise process that requires specific alignment and a "one-app-at-a-time" rule to prevent connection conflicts.

Here are the step-by-step instructions for a successful connection:

1. Pre-Connection Preparation

  • One App Rule: Completely close the FS Golf app before opening E6 Connect. Having multiple apps trying to talk to the radar at once will cause it to fail.

  • Charge & Power: Ensure your unit is powered on (hold the button until you hear a double beep).

  • Internet Check: Launch E6 Connect while connected to your home Wi-Fi first to ensure your profile is logged in and your licenses are validated.

2. Establish the Wi-Fi Link
  1. On your iOS device or PC, go to your Wi-Fi Settings.

  2. Select the network named after your unit's serial number (e.g., M2-123456 or X3-010234).

  3. Password: Enter your unit's full serial number as the password (e.g., M2-123456).

  4. Once connected, your device may say "No Internet Connection." This is normal; stay connected to the FlightScope Wi-Fi.

3. Configure E6 Connect
  1. Open E6 Connect.

  2. From the Main Menu, click the Settings (blue cogs) button.

  3. Select Simulator > Tracking System.

  4. Find FlightScope in the list and click Configure.

  5. The app should automatically detect your device. The status dot next to your serial number should turn Green.

  6. Set the Mode: Select your environment (e.g., Short Indoor, Indoor, or Outdoor).

  7. Adjust Distance: Manually enter the Sensor to Tee Distance (typically 8 feet for Mevo+).

4. Calibration & Alignment
  1. In the Configuration menu, click Align Camera. This uses the built-in FlightScope camera to ensure the radar is pointing directly down your target line.

  2. Tilt & Roll: Ensure the unit is set to exactly 12° (using the kickstand or the provided stencil) for simulation play.

  3. Click Accept to save your settings.

Troubleshooting Tips
  • "No Tracking System Found": Ensure "Local Network" access is enabled for E6 Connect in your iPad/iPhone Settings > Privacy & Security.

  • Manual vs. Auto: For older models like the Xi, you may need to select the "Manual" connection option if "Auto-Detect" fails.

  • PC Connectivity: If using a PC, ensure your Windows Firewall is not blocking E6 Connect, as this often prevents the "handshake" with the radar.

    • Related Articles

    • Connection issues with the Mevo

      Unable to get the Mevo + device to connect in the E6 Connect software Make sure the Mevo is updated with the latest firmware Eliminate WiFi interference. “Turn Off” other wifi devices in the home, this is especially true for Apple devices (like ...

    • How to connect GSA golf to E6 Connect

      Connecting your GSA Golf (Golf Simulator Association) hardware to E6 Connect typically involves using the GSA Golf Control Panel as the intermediary to send data to the E6 software. 1. Pre-Connection Setup GSA Interface: Ensure you have the latest ...

    • Tittle / SLX Connection to E6 Connect

      The SLX sensor uses Bluetooth Low Energy (BLE) to connect directly to the app. Do not pair the sensor in your iPad or PC's system Bluetooth settings. Power On: Press and hold the power button on the SLX sensor for about 3-5 seconds until the LED ...

    • Connecting Trackman to E6 Connect

      Connecting the TrackMan via Wi-Fi: Please use the link below for information on how to Connect the Trackman device in E6 Connect. https://e6golf.com/e6-connect/manual/#trackman Other Helpful links: https://mytrackman.com/support/software ...

    • Shots seem shorter in E6 Connect than in real life with Flightscope

      When shots appear shorter in E6 Connect compared to your real-world performance or even other apps like FS Golf, it is typically due to environment settings or physical setup, a "misalignment" between the radar and the software. 1. Check the "Tee ...