Apogee
Apogee How to submit logs to Trugolf.
Symptoms: You are have issues with your Apogee Launch Monitor. To help us improve we encourage both our technicians and customer to submit logs to TruGolf. This will be forwarded to support so we can reach out and address issue and concerns. How to ...
Apogee camera appears out focus (blurry)
Symptoms: One of the two camera's will appear blurry or out of focus during the calibration stages. This is most likely to occur during the alignment phase of calibration, but can also happen during offset lighting stage. The Apogee may or may not ...
Apogee how to allow through Windows Firewall
Symptoms: Apogee might not be connecting to the PC. This might happen during a new install or an update. The Apogee installer can prompt for allowing through Windows Defender Firewall rules but this can get covered up and missed and the installation ...
Apogee unable to connect to PC
Issue: The apogee is showing red or blue up at the top but when opening AID it displays an orange banner and the status in the dashboard shows no internet connection. *Note: Apogee uses cat 6 network cable to connect to either a direct ethernet port, ...
Apogee Flashing Red Banner and Strobes Flashing
Symptoms: The Apogee Logo banner may show red and even flash on and off. This can also show the IR circuits boards flashing on and off. This will likely occur during calibration during the alignment phase. You may also see the cameras showing black ...
Apogee How to find the serial number/Model Differences
Locating an Apogee's Serial Number: All serial number are located on the back of the unit. The first Beta and Gamma units had white sticker and was located some where on the back starting with G22-xxxx or G23-xxxx. Delta and late Gamma unit will have ...
Apogee Voice Commands not responding
Issue: Some user may report Apogee Voice Commands are not responding. Resolution: Always inspect the microphone on the unit for physical obstruction. Have users test voice command up close standing under the unit. If possible try different user ...
Apogee no laser
Issue: Users may report they are getting no active laser on the turf when either trying to calibrate or during play in E6Connect. A laser may not show during any phase of calibration or at the final stage at the end of Calibration (during Take A ...
Apogee fans showing red in Status
Issue: Customer may report they are unable to use the apogee stating there is red banner up at the top and they (or hardware support) has check the status from the Apogee Intelligent Dashboard.) When opening AID main Menu select Status. When inside ...
How to Calibrate Apogee (Current -Firmware .85 and higher)
Issue: Customers may report or request needing Assistance Calibrating *Note: AID calibration differs in order of operations. Auto Lighting features have been added to newer version of .85 and higher. Resolution: ACC is now legacy and can longer ...
Apogee 0 Degree Not ready
Issue: Shots aren't registering, ball is not detected, and error "0 Degree not ready" as shown below: Resolution: The Apogee Tracking system is not selected Note: this could be due to it's a first time install or new device has been installed due ...
How to update Apogee Firmware (for version lower than .50)
Issue: How to update to the latest Firmware and Apogee Intelligent Dashboard. To update the apogee unit first download AID from https://trugolf.com/pages/support (download the latest version for all newer units). *Note AID 1.19 will be showing on the ...
What's in the box? Apogee package includes
Packaged Items Hardware APOGEE Launch Monitor APOGEE Ceiling Mount Paper APOGEE Calibration Template Use this to complete calibration inside the APOGEE Control Center Software. “Hey APOGEE,” Voice Command Instructions User Guide to the Voice Command ...
How to install/mount APOGEE (Resellers/Self Installer)
How to install/Mount Apogee (Resellers/Self Installer) Issues: How do I mount the Apogee unit? FAQ’S (See attached PDF) Resolution: The Apogee Manual covers how the mounting of the unit is to be done. Most of the installation process should be ...